Lathe tailstock assembly drawing ppt templates

images lathe tailstock assembly drawing ppt templates

Operations commonly performed on a lathe include turning, facing, form turning, grooving, drilling,boring, knurling, taper turning and thread cutting. It is used for parts,that must be dissembled for during operations of a machine. Similarly, cam-operated screw machines and chuckers did not disappear; they simply shifted to a different niche. Fit is defined as the degree of freedom of tightness between the mating parts in an assembly process. Lathe accessories include centres, catch plates and carriers, chucks, face plates, angle plates,mandrels, and rests. The first turret lathe was invented by Stephen Fitch in Example of Slide fit :. Skip Navigation.

  • Workshop Practice Lesson INTRODUCTION TO LATHE MACHINE
  • Analysis and design of tail stock assembly
  • Machine Drawing Tailstock of Lathe
  • What is the Fit and what are the Different types of Fits

  • About five years ago, I looked around for a lathe that would swing 24 in. over the bed.

    Workshop Practice Lesson INTRODUCTION TO LATHE MACHINE

    shop can probably do the machining for you, working from the drawings. The flat plates that make up the tailstock assembly, and other parts here and. Connector Square Tool Post Milling Fixture Radial Engine Sub-assembly Eccentric Rotary Gear Head Slide Lathe Tail-stock Milling Machine Tail-stock.

    Assembly and Details machine drawing pdf Lathe Parts, Lathe Machine, Cad Cam, Cad framed and would suit perfectly with an industrial/mechanical theme.
    The work piece is supported between centres or in any other work holding device, and rotated at the desired speed. The workplace is held between centres or attached to the face plate. Thus the duties of the operator, which were already greatly reduced by the manual turret lathe, were even further reduced, and productivity increased.

    In this way, a sequence of operations can be performed on a part without switching tools with each operation.

    images lathe tailstock assembly drawing ppt templates

    No cutting is involved in the knurling process.

    images lathe tailstock assembly drawing ppt templates
    Lathe tailstock assembly drawing ppt templates
    They were used extensively in the mass production for the war effort in World War II.

    Howe, Richard S. It is a small lathe that is mounted on a work bench.

    Video: Lathe tailstock assembly drawing ppt templates Tail Stock Assembly

    Example of Easy slide fit : piston and slide valves and spindle of lathe. The term "turret lathe" without further qualification is still understood to refer to this type. From the lateth through midth centuries, turret lathes, both manual and automatic i. The latter is due to the toolpath's being controlled by the machine, either in jig -like fashion, via the mechanical limits placed on it by the turret's slide and stops, or via electronically -directed servomechanisms for computer numerical control lathes.

    CIM Oct, April - ,CIM Oct, April -April -Oct Question Papers · Machine Drawing KEY (solution).

    presentation of it.

    images lathe tailstock assembly drawing ppt templates

    this direction, complete revision of the chapter on assembly drawings is done. Examples of such drawings are: lathe tail-stock, diesel. TAILSTOCK A tailstock, also known as a foot stock, is a device often used as part of an engineering lathe, wood- turning lathe, or used in.
    Tapers areused on many tools and machine components for alignment and for easy holding. Workshop Practice You are currently using guest access Log in.

    Production lathe Automatic lathe, capstan and turret lathe. Bloomington, Indiana: Xlibris. Unlike bench lathes, engine lathes, and toolroom lathes, on which each tool change involved some amount of setup, and toolpath had to be carefully controlled by the operator, turret lathes allowed the multiple tool changes and toolpaths of one part-cutting cycle to be repeated with little time or effort.

    Video: Lathe tailstock assembly drawing ppt templates Draw TAILSTOCK assembly, parts of a TAILSTOCK , lathe and TAILSTOCK

    Production lathes are machines designed to produce large number of duplicate parts faster and with less skill and labour. The minimum diameter of hole is grater then large diameter of the shaft.

    images lathe tailstock assembly drawing ppt templates
    Lathe tailstock assembly drawing ppt templates
    Pulley mounted on the shaft forms a fixed joint.

    Engine lathe is the most important member of the lathe family and the most commonly used. Examples of Tight fit : Stepped pulleys on the drive shaft of a conveyors,cylindrical grinding machine. The term "turret lathe" encompasses them all. The carriage assembly of the lathe comprises of a number of components which support, move and control the tool.

    Analysis and design of tail stock assembly

    The head stock houses the spindle and the means for supporting and rotating the spindle.

    The examples on the right come from a good page: Winter 8.

    Tolerances. From the previous drawing, we see useful information in the title block milling machine (or mill): rectangular parts, hole patterns usually with drill bit (possibly followed by reamer) in tail stock; but can use boring bar to make larger holes. Lathe Bed. Presentation on theme: "1. Bed 2. Headstock 3.

    Machine Drawing Tailstock of Lathe

    Tailstock 4 Three major units mounted on bed are the head-stock, the tail stock, and the carriage. presentation of it. Prof this direction, complete revision of the chapter on assembly drawings is done. . Examples of such drawings are: lathe tail-stock, diesel.
    Root of Colt ; J.

    images lathe tailstock assembly drawing ppt templates

    It is used for small work pieces having a maximum swing of mm at the face plate. In other projects Wikimedia Commons. The power to the engine lathe spindle may be given with the help of a belt drive from an overhead line shaft but most modern machines have a captive motor with either a cone pulley drive or an all geared head stock arrangement. With the development and dissemination of CNC lathes, which themselves often have automated turrets, manual turret lathes began to lose their position as the key to mass production of turned parts.

    How to use the coordinate system in the drawing and manufacturing templates by admin July 28,

    images lathe tailstock assembly drawing ppt templates
    Lathe tailstock assembly drawing ppt templates
    Slack running Fits :.

    What is the Fit and what are the Different types of Fits

    This are not disassembled during their service life. After this, a front tool on the cross slide could cut a groove in the knurled area, providing a chamferand then a rear tool would be brought forward to cut the finished screw from the bar, called "parting it off". The work piece may be supported between centres. This is the simplest of all lathes. The roller serrations are at 45 degrees to the horizontal but 90degrees to each other so that a diamond shaped pattern is produced by amechanical working process.

    Which can be made to overlap to produce a cylindrical surface on the work piece by adjusting the feed and having a large nose radius.